“the natural way to better health”  
General
General Kit information
General Test Kit
General Kit
  prepare to test
General Kit
  how to test
General Kit
  tips to test baby and paint
General kit
  reading results
General kit
  samples of results
General kit
  high heavy metals results

Other Metals Test
Aluminium
Arsenic
Cadmium
Chromium
Cobalt
Copper
Iron
Lead
Mercury
Manganese
Molybdenum
Silver
Thallium
Tin
Zinc

Other Self-tests
Free Radical Test
Water Test Kit (2-test pack)
Adrenal Function Urine Test
Sulkowitch Urine (Calcium) Test
pH Indicators strips
10-P Urine Analysis

Heavy Metals Detox

MF (metal free) Water

Natural Nutritional Products

Practitioner Registration & Log in

Strategic Health Markers
Energy
pH Indicator
Free Radicals
Inflammation



Heavy Metals Test - General Kit

Monitor your body and environment for HEAVY METALS contamination



Heavy Metals tested:
CADMIUM, COBALT, COPPER, LEAD, MANGANESE,
MERCURY, NICKEL, ZINC





Preparation of Test Solution
  1. Remove cap from test tube
  2. Empty clear liquid content in vial into test tube
  3. Cap the test tube and turn test tube so that the cap is facing the ground. Then shake until solution has turn green
  4. The solution containing the reagents has now been activated and is ready to test the sample solution for presence of heavy metals mentioned above
    The testing must be conducted within 30 minutes of activating the test solution otherwise it will deteriorate

Conducting the test
  1. Add the required volume of the sample solution (saliva, urine, water, etc.) to be tested into the green test solution in the test tube with the pipette provided
  2. Close the test tube with the cap provided and shake vigorously.
  3. Allow the solution to stand on the cap of the test tube for 1 minute (see below if testing urine)**
  4. Observe the band or ring of about 1 cm. wide just below the surface of the solution in the test tube. A colour change will indicate the presence of heavy metals (see chart on label of kit)
  5. If the ring turns gray it indicates that there is more than one heavy metal present at the same low level of concentration
  6. If there is no change in colour (ie., the solution remains green), there are no heavy metals present

A strong colour is indicative of the presence of the metal indicated to at least 5 ppm
The colour results were validated by Kemetco Research Inc. based in Richmond, British Columbia, Canada - 2008


When ** urine is tested, the solution may be more stable and the colour may not change for up to 10 minutes. The solution will turn to yellow-orange after 30 minutes. This is caused by the decomposition of the reagents used in the test solution and should be ignored


"I purchased 4 of ur “Heavy Metal Test General Kit” in U.K. which confirmed my doctors laboratory test that I have lead poison from lead water main to apt. Enviromental Health Dept tests on water recorded 1040 uj of lead where EEC safety limit was 15uj!

Clearly,ur product works ....."

Dr. David Boyce
Argyll, Scotland, United Kingdom




See tips on how to test your baby and paint for heavy metals




Images of the General Test Kit, contents and colour chart to check result of test

A strong colour is indicative of the presence of the metal indicated to at least 5 ppm
The colour results were validated by Kemetco Research Inc. based in Richmond, British Columbia, Canada - 2008






The above information is provided for general educational purposes only. It is not intended to replace competent health care advice received from a knowledgeable healthcare professional. You are urged to seek healthcare advice for the treatment of any illness or disease.
Health Canada and the FDA (USA) have not evaluated these statements. This product is not intended to diagnose, treat, cure, or prevent any disease.

 


 Resellers/Distributors - Nth America | Sth America | Asia | Europe | Africa | Oceania | CONTACT |  Contact
Copyright 2001-2015 Osumex Natural Alternatives Ltd. All rights reserved.